Как установить Lucent Win modem??
-
Anonymous
Как установить Lucent Win modem??
Люди плиз помогите как поставить сранный модем???у меня модем Agere System Soft Modem!!!!Чипсет Lucent !!!Опишите пожалуста подробно или стукните в асю 276984763!!!!
-
Anonymous
Установка модема Lucent на Linux.
1. Идём в интернет по адресу http://www.heby.de/ltmodem/ и качаем оттуда драйвер типа ltmodem-8.xxxx.tar.gz (размером около 500kb). Драйвер должен соответствовать вашей версии ядра. Например, у меня ASPLinux 9.2 и ядро 2.4.25, и для моего ядра подошёл драйвер ltmodem-8.30a9.tar.gz.
2. Распаковываем архив драйвера в какую-нибудь папку. Здесь мы видим файл build_module.
3. Открываем именно в этой папке консоль и запускаем с правами хозяина этот скрипт:
$ ./build_module
4. Даный скрипт будет постоянн просить нажимать Enter. Нажимайте.
5. После завершения build_module сразу же запускаете скрипт ltinst2:
$ ./ltinst2
6. После ltinst2 тут же в консоли запускаете скрипт autoload
$ ./autoload
Всё - драйвер установлен. Перезагружаете компьютер. Запускаете программу KPPP - здесь модем должен определится как стандартный модем.
Внимание: Для установки драйвера необходимо, что бы в системе были установлены следующие компоненты: полные исходники ядра, binutils, GNU make, gcc. Если этх компонентов не будет или они будут не той версии, то скрипт build_module выведет соответствующие сообщения ( на аглицком языке). Так что постарайтесь, если драйвер не устанавливается, прочитать сообщения build_module.
1. Идём в интернет по адресу http://www.heby.de/ltmodem/ и качаем оттуда драйвер типа ltmodem-8.xxxx.tar.gz (размером около 500kb). Драйвер должен соответствовать вашей версии ядра. Например, у меня ASPLinux 9.2 и ядро 2.4.25, и для моего ядра подошёл драйвер ltmodem-8.30a9.tar.gz.
2. Распаковываем архив драйвера в какую-нибудь папку. Здесь мы видим файл build_module.
3. Открываем именно в этой папке консоль и запускаем с правами хозяина этот скрипт:
$ ./build_module
4. Даный скрипт будет постоянн просить нажимать Enter. Нажимайте.
5. После завершения build_module сразу же запускаете скрипт ltinst2:
$ ./ltinst2
6. После ltinst2 тут же в консоли запускаете скрипт autoload
$ ./autoload
Всё - драйвер установлен. Перезагружаете компьютер. Запускаете программу KPPP - здесь модем должен определится как стандартный модем.
Внимание: Для установки драйвера необходимо, что бы в системе были установлены следующие компоненты: полные исходники ядра, binutils, GNU make, gcc. Если этх компонентов не будет или они будут не той версии, то скрипт build_module выведет соответствующие сообщения ( на аглицком языке). Так что постарайтесь, если драйвер не устанавливается, прочитать сообщения build_module.
-
Anonymous
Люди вот такая борода (когда пришу ./build_module):
Lucent/Agere_Systems(AS) DSP chip modems (but Not the AMR or soft PCI chipsets) are supported by the the resources of this kit.
AS maintainer S. Sarkar develops the code on a Red Hat Linux test bed.
The lt_serial.o Serial Interface module comes under GPL and is Open Source.
The lt_modem.o code is entirely proprietary, though partially Open Source.
Adaptation to ongoing changes in Linux source code is enabled by the Open Source components.
Critical AS proprietary information is pre-complied in ltmdmobj.o,
whose constituents are functionally not affected by minor Linux source code changes.
Volunteer maintainers periodically receive code updates from AS.
Through the contributions of Many described in CREDITS, there are
enhancements in utility, ease of installation and documentation.
Mark Spieth initiated this ltmodem compiler kit series.
Chris Hebeisen introduced the Configure implementation, bringing Newbie friendliness.
Marv Stodolsky is culpable for the verbose messaging.
Within DOCs/, Ltmodem.html has URLs to many particular usage cases.
Volunteers assemble the ltmodem-version.deb and
ltmodem-version.rpm Installers for the User Community as Linux source code evolves
utiliizing the resources of this compiler kit series.
If new to compiling, read the ModemCompiling.txt which is being output, to guide
proper set up your kernel-sources. The kernel-source package as installed does
NOT in general match an installed kernel, but one of several alternative kernels.
Thus with a niave usage, all could be completed well technically.
BUT the installed drivers might not be compatible with your kernel,
of even reside in the needed /lib/modules/Kernel_Version/ tree.
To continue, Enter
This compilation process is likely Not necessary to work through,
if the only need is modem drivers matching the standard kernel of the
following Linux distributions: Debian, Red Hat, Mandrake, SuSE and Connectiva
Volunteers have already compiled most standard drivers. For more current releases,
those available compatible with your System requirements will be later listed.
They are available for download as ltmodem-version.rpm and
ltmodem-version.deb Installers from a repository, http://ltmodem.heby.de
If your System can use one of these Installers, you will be informed below.
Many installers for older kernels are available at:
http://linmodems.technion.ac.il/packages.html
The compiling process is a learning experience for Newbies.
We strongly recommend that you DO learn it sometime.
But getting on the Internet under Linux should have first priority.
This kit provides several diagnostics aids and good documentation.
Continuing will do no harm. Useful diagnostic information
on your system will be written to BLDrecord.txt,
with direction to documentation if a failure occurs.
At a minimum, Do keep the DOCs/ and utils/ folders and become familiar
with the resources therein.
To continue: Enter
=================================================================
This is the version 8.31a10 of the compiler + installer kit
8.31 corresponds to the version of the core Agere Systems DSP code.
a10 designation that follows reflects NO improvement in DSP code.
Rather peripheral driver, added diagnostics and installer improvements
are reflected. They are progressively implemented as Users report problems
or the Linux kernel evolves.
The modem drivers will serve with Linux kernels beginning with 2.2.2, the current
2.4.nn series, and the 2.5.nn development kernels.
However support was broken in the early 2.4.n-test series.
When there is a Red Hat 2.6.nn release, AS will then update the code
If your PC is being well served with this 8.31a10,
there is NO Benefit in using a more recent version
until there is an update in the Agere driver code, say 8.26 to 9.00.
But if the driver installation for a new kernel should in some way fail,
please do download the most recent ltmodem-VER.tar.gz
before sending a query to discuss@linmodems.org,
because the problem may already be solved.
This build_module script only compiles drivers,
with their installation managed by subsequent commands.
Thus ./build_module can be rerun for education or amusement,
without as yet committing changes to your System.
For general instructions: Enter
=================================================================
All should work automatically for most Linux installations/distributions,
IF a complete kernel-headers/ folder is available:
through a symbolic link: /lib/modules/KernelVersion/build --> PATH_to/kernel-headers/
at the classical /usr/src/ position.
Otherwise a symbolic link will be necessary:
ln -s PATH_to/kernel-headers/ /usr/src/linux
Read ModemDriverCompiling.txt if an explanation is needed about kernel-headers.
To compile modules for a kernel other version than 2.4.22-1.2129.nptl, such as version 2.2.17-3test, use syntax:
./build_module 2.2.17-3test
where the version.h in the kernel-headers/ folder has 2.2.17-3test
If desirable to make a record for trouble shooting purposes,
Abort with Ctrl-C. Then the process can be recorded to ltrecord.txt :
./build_module | tee ltrecord.txt
To continue: Enter
====================================================================
Diagnostic information is progressively being written to BLDrecord.txt .
Often, contents of BLDrecord.txt will aid in solving a problem.
The Linux distribution is: redhat, Linux XP Professional Edition 1 (Phantom Menace)
End of distribution check.
UPDATE=2004_Nov_26
TMPM=0tmpfile
Providing detail for device at PCI_bus 00:0c.0
with vendor-ID:device-ID
----:----
Class 0780: 11c1:048c Communication controller: Lucent Microelectronics: Unknown device 048c (rev 02)
SubSystem 11c1:044c Lucent Microelectronics: Unknown device 044c
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at e3001000 (32-bit, non-prefetchable)
I/O ports at d800
-----PCI_IDs------- --CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 11c1:048c 11c1:044c redhat 2.4.22-1.2129.nptl 3.2.3 3.3.2 i686
IDENT=AGERE
PCIDEV=11c1:048c
Vendor=11c1
To continue: Enter==================================================
Checking for any preliminary complications.
The kernel supports only single processor motherboards.
To continue: Enter==================================================
OK thus far.
To begin acquisition of compiling information: Enter
Removing old makings and expanding a clean source.tar.gz
Setting BLDrecord.txt link within source/ folder.
lrwxrwxrwx 1 root root 16 Янв 20 19:31 BLDrecord.txt -> ../BLDrecord.txt
Setting ./tmpfile link within source/ folder.
lrwxrwxrwx 1 root root 12 Янв 20 19:31 ./tmpfile -> .././tmpfile
Following a successful check for matching kernel-headers,
the modem drivers will be compiled for the current kernel version: 2.4.22-1.2129.nptl
To start resource tests: Enter
Performing a configure trial and capturing the report to ../conf-report.txt.
Parsing the report:
No evident problems.
creating cache ./config.cache
Checking OS
Checking machine type
Processor i686 is supported.
checking for gcc... gcc
checking whether the C compiler (gcc ) works... yes
checking whether the C compiler (gcc ) is a cross-compiler... no
checking whether we are using GNU C... yes
checking whether gcc accepts -g... yes
Checking gcc major version 3
Checking for rpm build... rpmbuild
checking for a BSD compatible install... /usr/bin/install -c
checking for make... yes
checking for ld... yes
Checking for kernel headers
... in /usr/src/linux: nope
... in /usr/src/kernel-headers-2.4.22-1.2129.nptl: nope
... in /usr/src/linux-2.4.22: nope
... in /usr/src/linux-2.4.22-1.2129.nptl: Kernel headers found in /usr/src/linux-2.4.22-1.2129.nptl
... in /lib/modules/2.4.22-1.2129.nptl/build: Kernel headers found in /lib/modules/2.4.22-1.2129.nptl/build
using /lib/modules/2.4.22-1.2129.nptl/build
Checking kernel header version
kernel headers are version 2.4.22-1.2129.nptl
RPM will require kernel = 2.4.22-1.2129.nptl
has irq_spinlock in async_struct 1
checking for fakeroot... no
+-----------------------------------------------------------------------------+
| will have to be root. Otherwise this won't affect you. |
+-----------------------------------------------------------------------------+
updating cache ./config.cache
creating ./config.status
creating Makefile
creating ltinst2
creating Makefile.2.4
creating autoload
creating cleanup
creating ltmodem.spec
The check for compilation tools and general resources was successful.
Within DOCs/ there is an annotated conf-report.txt
The Makefile and down steam installation scripts have been created.
To continue:
EnterNext checking for the the needed header file: modversions.h
Found: /lib/modules/2.4.22-1.2129.nptl/build/include/linux/modversions.h
Next checking utilty versions,
Version_min
Utility or range for kernels
name 2.2.16 2.4.18 Actual_version
-------------------------------------------------------------------
Gnu C 2.7.2.3 2.95.3-2.9.99 3.3.2
Gnu make 3.77 3.79.1
binutils 2.8.1.0.23 2.9.1.0.25 2.14.90.0.6
-------------------------------------------------------------------
The gcc compiler resources available are:
----------------------------
-rwxr-xr-x 2 root root 80676 Окт 23 2003 /usr/bin/gcc
-rwxr-xr-x 2 root root 81864 Фев 12 2003 /usr/bin/gcc296
-rwxr-xr-x 1 root root 76548 Июн 3 2003 /usr/bin/gcc32
----------------------------
with your System currently using version 3.3.2
Do NOT mix the major versions of compilers for the kernel and modem drivers
or your System will crash! The following releases are using gcc version 3.2.x : Mandrake 9, Redhat 8 and SuSE 8.1 in November 2002.
To continue:
Enter
To begin compilation of lt_modem.o and lt_serial.o, Enter
To avoid faulting Systems with an Enviromental setting: make -e
make
is the compiling command used with build_module.
To modify "make" invocation on your System, if desirable,
edit the build_module line below: MAKEE
Makefile:103: предупреждение: перекрытие команд для цели `uninstall'
Makefile.2.4:170: предупреждение: игнорирование старых команд для цели `uninstall'
ltmodem.c: In function `dp_regread':
ltmodem.c:478: warning: `flags' might be used uninitialized in this function
serial-lt-2.4.c: In function `lt_rs_interrupt':
serial-lt-2.4.c
error: `info' undeclared (first use in this function)
serial-lt-2.4.c error: (Each undeclared identifier is reported only once
serial-lt-2.4.c error: for each function it appears in.)
make: *** [serial-lt-2.4.a] Ошибка 1
Using KCFLAGS for gcc version 3.x
gcc -D__KERNEL__ -I/lib/modules/2.4.22-1.2129.nptl/build/include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -fno-strict-aliasing -pipe -fno-strength-reduce -DMODULE -DLT_VERSION=8.31a10 -DLINUX -DNO_EEPROM -DLT_SERIAL_MODULE=lt_serial -DFORCEMODVERSIONS -DASMLINKAGE=asmlinkage -DHAS_IRQSPINLOCK -c -o ltmodem.a ltmodem.c
objcopy -W x_input --redefine-sym memset=ltmodem_memset ltmdmobj.o ./xxx.o
ld -r -defsym x_input_orig=x_input -o ./xxx1.o ./xxx.o
ld -r -d -o lt_modem.o ltmodem.a ./xxx1.o
rm -f ./xxx.o
rm -f ./xxx1.o
#ld -r -o lt_modem.o ltmodem.a ltmdmobj.o
Using KCFLAGS for gcc version 3.x
gcc -D__KERNEL__ -I/lib/modules/2.4.22-1.2129.nptl/build/include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -fno-strict-aliasing -pipe -fno-strength-reduce -DMODULE -DLT_VERSION=8.31a10 -DLINUX -DNO_EEPROM -DLT_SERIAL_MODULE=lt_serial -DFORCEMODVERSIONS -DASMLINKAGE=asmlinkage -DHAS_IRQSPINLOCK -c -o serial-lt-2.4.a serial-lt-2.4.c
Checking for driver products:
-rw-r--r-- 1 root root 557900 Янв 20 19:31 lt_modem.o
Compilation of lt_serial.o failed,
Do assess whether your utilities are up to date as listed within 1ST-READ!
Read Compile_properly.txt from DOCs/.
If you cannot solve the problem, send BLDrecord.txt to: discuss@linmodems.org
Lucent/Agere_Systems(AS) DSP chip modems (but Not the AMR or soft PCI chipsets) are supported by the the resources of this kit.
AS maintainer S. Sarkar develops the code on a Red Hat Linux test bed.
The lt_serial.o Serial Interface module comes under GPL and is Open Source.
The lt_modem.o code is entirely proprietary, though partially Open Source.
Adaptation to ongoing changes in Linux source code is enabled by the Open Source components.
Critical AS proprietary information is pre-complied in ltmdmobj.o,
whose constituents are functionally not affected by minor Linux source code changes.
Volunteer maintainers periodically receive code updates from AS.
Through the contributions of Many described in CREDITS, there are
enhancements in utility, ease of installation and documentation.
Mark Spieth initiated this ltmodem compiler kit series.
Chris Hebeisen introduced the Configure implementation, bringing Newbie friendliness.
Marv Stodolsky is culpable for the verbose messaging.
Within DOCs/, Ltmodem.html has URLs to many particular usage cases.
Volunteers assemble the ltmodem-version.deb and
ltmodem-version.rpm Installers for the User Community as Linux source code evolves
utiliizing the resources of this compiler kit series.
If new to compiling, read the ModemCompiling.txt which is being output, to guide
proper set up your kernel-sources. The kernel-source package as installed does
NOT in general match an installed kernel, but one of several alternative kernels.
Thus with a niave usage, all could be completed well technically.
BUT the installed drivers might not be compatible with your kernel,
of even reside in the needed /lib/modules/Kernel_Version/ tree.
To continue, Enter
This compilation process is likely Not necessary to work through,
if the only need is modem drivers matching the standard kernel of the
following Linux distributions: Debian, Red Hat, Mandrake, SuSE and Connectiva
Volunteers have already compiled most standard drivers. For more current releases,
those available compatible with your System requirements will be later listed.
They are available for download as ltmodem-version.rpm and
ltmodem-version.deb Installers from a repository, http://ltmodem.heby.de
If your System can use one of these Installers, you will be informed below.
Many installers for older kernels are available at:
http://linmodems.technion.ac.il/packages.html
The compiling process is a learning experience for Newbies.
We strongly recommend that you DO learn it sometime.
But getting on the Internet under Linux should have first priority.
This kit provides several diagnostics aids and good documentation.
Continuing will do no harm. Useful diagnostic information
on your system will be written to BLDrecord.txt,
with direction to documentation if a failure occurs.
At a minimum, Do keep the DOCs/ and utils/ folders and become familiar
with the resources therein.
To continue: Enter
=================================================================
This is the version 8.31a10 of the compiler + installer kit
8.31 corresponds to the version of the core Agere Systems DSP code.
a10 designation that follows reflects NO improvement in DSP code.
Rather peripheral driver, added diagnostics and installer improvements
are reflected. They are progressively implemented as Users report problems
or the Linux kernel evolves.
The modem drivers will serve with Linux kernels beginning with 2.2.2, the current
2.4.nn series, and the 2.5.nn development kernels.
However support was broken in the early 2.4.n-test series.
When there is a Red Hat 2.6.nn release, AS will then update the code
If your PC is being well served with this 8.31a10,
there is NO Benefit in using a more recent version
until there is an update in the Agere driver code, say 8.26 to 9.00.
But if the driver installation for a new kernel should in some way fail,
please do download the most recent ltmodem-VER.tar.gz
before sending a query to discuss@linmodems.org,
because the problem may already be solved.
This build_module script only compiles drivers,
with their installation managed by subsequent commands.
Thus ./build_module can be rerun for education or amusement,
without as yet committing changes to your System.
For general instructions: Enter
=================================================================
All should work automatically for most Linux installations/distributions,
IF a complete kernel-headers/ folder is available:
through a symbolic link: /lib/modules/KernelVersion/build --> PATH_to/kernel-headers/
at the classical /usr/src/ position.
Otherwise a symbolic link will be necessary:
ln -s PATH_to/kernel-headers/ /usr/src/linux
Read ModemDriverCompiling.txt if an explanation is needed about kernel-headers.
To compile modules for a kernel other version than 2.4.22-1.2129.nptl, such as version 2.2.17-3test, use syntax:
./build_module 2.2.17-3test
where the version.h in the kernel-headers/ folder has 2.2.17-3test
If desirable to make a record for trouble shooting purposes,
Abort with Ctrl-C. Then the process can be recorded to ltrecord.txt :
./build_module | tee ltrecord.txt
To continue: Enter
====================================================================
Diagnostic information is progressively being written to BLDrecord.txt .
Often, contents of BLDrecord.txt will aid in solving a problem.
The Linux distribution is: redhat, Linux XP Professional Edition 1 (Phantom Menace)
End of distribution check.
UPDATE=2004_Nov_26
TMPM=0tmpfile
Providing detail for device at PCI_bus 00:0c.0
with vendor-ID:device-ID
----:----
Class 0780: 11c1:048c Communication controller: Lucent Microelectronics: Unknown device 048c (rev 02)
SubSystem 11c1:044c Lucent Microelectronics: Unknown device 044c
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at e3001000 (32-bit, non-prefetchable)
I/O ports at d800
-----PCI_IDs------- --CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 11c1:048c 11c1:044c redhat 2.4.22-1.2129.nptl 3.2.3 3.3.2 i686
IDENT=AGERE
PCIDEV=11c1:048c
Vendor=11c1
To continue: Enter==================================================
Checking for any preliminary complications.
The kernel supports only single processor motherboards.
To continue: Enter==================================================
OK thus far.
To begin acquisition of compiling information: Enter
Removing old makings and expanding a clean source.tar.gz
Setting BLDrecord.txt link within source/ folder.
lrwxrwxrwx 1 root root 16 Янв 20 19:31 BLDrecord.txt -> ../BLDrecord.txt
Setting ./tmpfile link within source/ folder.
lrwxrwxrwx 1 root root 12 Янв 20 19:31 ./tmpfile -> .././tmpfile
Following a successful check for matching kernel-headers,
the modem drivers will be compiled for the current kernel version: 2.4.22-1.2129.nptl
To start resource tests: Enter
Performing a configure trial and capturing the report to ../conf-report.txt.
Parsing the report:
No evident problems.
creating cache ./config.cache
Checking OS
Checking machine type
Processor i686 is supported.
checking for gcc... gcc
checking whether the C compiler (gcc ) works... yes
checking whether the C compiler (gcc ) is a cross-compiler... no
checking whether we are using GNU C... yes
checking whether gcc accepts -g... yes
Checking gcc major version 3
Checking for rpm build... rpmbuild
checking for a BSD compatible install... /usr/bin/install -c
checking for make... yes
checking for ld... yes
Checking for kernel headers
... in /usr/src/linux: nope
... in /usr/src/kernel-headers-2.4.22-1.2129.nptl: nope
... in /usr/src/linux-2.4.22: nope
... in /usr/src/linux-2.4.22-1.2129.nptl: Kernel headers found in /usr/src/linux-2.4.22-1.2129.nptl
... in /lib/modules/2.4.22-1.2129.nptl/build: Kernel headers found in /lib/modules/2.4.22-1.2129.nptl/build
using /lib/modules/2.4.22-1.2129.nptl/build
Checking kernel header version
kernel headers are version 2.4.22-1.2129.nptl
RPM will require kernel = 2.4.22-1.2129.nptl
has irq_spinlock in async_struct 1
checking for fakeroot... no
+-----------------------------------------------------------------------------+
| will have to be root. Otherwise this won't affect you. |
+-----------------------------------------------------------------------------+
updating cache ./config.cache
creating ./config.status
creating Makefile
creating ltinst2
creating Makefile.2.4
creating autoload
creating cleanup
creating ltmodem.spec
The check for compilation tools and general resources was successful.
Within DOCs/ there is an annotated conf-report.txt
The Makefile and down steam installation scripts have been created.
To continue:
EnterNext checking for the the needed header file: modversions.h
Found: /lib/modules/2.4.22-1.2129.nptl/build/include/linux/modversions.h
Next checking utilty versions,
Version_min
Utility or range for kernels
name 2.2.16 2.4.18 Actual_version
-------------------------------------------------------------------
Gnu C 2.7.2.3 2.95.3-2.9.99 3.3.2
Gnu make 3.77 3.79.1
binutils 2.8.1.0.23 2.9.1.0.25 2.14.90.0.6
-------------------------------------------------------------------
The gcc compiler resources available are:
----------------------------
-rwxr-xr-x 2 root root 80676 Окт 23 2003 /usr/bin/gcc
-rwxr-xr-x 2 root root 81864 Фев 12 2003 /usr/bin/gcc296
-rwxr-xr-x 1 root root 76548 Июн 3 2003 /usr/bin/gcc32
----------------------------
with your System currently using version 3.3.2
Do NOT mix the major versions of compilers for the kernel and modem drivers
or your System will crash! The following releases are using gcc version 3.2.x : Mandrake 9, Redhat 8 and SuSE 8.1 in November 2002.
To continue:
Enter
To begin compilation of lt_modem.o and lt_serial.o, Enter
To avoid faulting Systems with an Enviromental setting: make -e
make
is the compiling command used with build_module.
To modify "make" invocation on your System, if desirable,
edit the build_module line below: MAKEE
Makefile:103: предупреждение: перекрытие команд для цели `uninstall'
Makefile.2.4:170: предупреждение: игнорирование старых команд для цели `uninstall'
ltmodem.c: In function `dp_regread':
ltmodem.c:478: warning: `flags' might be used uninitialized in this function
serial-lt-2.4.c: In function `lt_rs_interrupt':
serial-lt-2.4.c
error: `info' undeclared (first use in this function)serial-lt-2.4.c
error: (Each undeclared identifier is reported only onceserial-lt-2.4.c
error: for each function it appears in.)make: *** [serial-lt-2.4.a] Ошибка 1
Using KCFLAGS for gcc version 3.x
gcc -D__KERNEL__ -I/lib/modules/2.4.22-1.2129.nptl/build/include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -fno-strict-aliasing -pipe -fno-strength-reduce -DMODULE -DLT_VERSION=8.31a10 -DLINUX -DNO_EEPROM -DLT_SERIAL_MODULE=lt_serial -DFORCEMODVERSIONS -DASMLINKAGE=asmlinkage -DHAS_IRQSPINLOCK -c -o ltmodem.a ltmodem.c
objcopy -W x_input --redefine-sym memset=ltmodem_memset ltmdmobj.o ./xxx.o
ld -r -defsym x_input_orig=x_input -o ./xxx1.o ./xxx.o
ld -r -d -o lt_modem.o ltmodem.a ./xxx1.o
rm -f ./xxx.o
rm -f ./xxx1.o
#ld -r -o lt_modem.o ltmodem.a ltmdmobj.o
Using KCFLAGS for gcc version 3.x
gcc -D__KERNEL__ -I/lib/modules/2.4.22-1.2129.nptl/build/include -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer -fno-strict-aliasing -pipe -fno-strength-reduce -DMODULE -DLT_VERSION=8.31a10 -DLINUX -DNO_EEPROM -DLT_SERIAL_MODULE=lt_serial -DFORCEMODVERSIONS -DASMLINKAGE=asmlinkage -DHAS_IRQSPINLOCK -c -o serial-lt-2.4.a serial-lt-2.4.c
Checking for driver products:
-rw-r--r-- 1 root root 557900 Янв 20 19:31 lt_modem.o
Compilation of lt_serial.o failed,
Do assess whether your utilities are up to date as listed within 1ST-READ!
Read Compile_properly.txt from DOCs/.
If you cannot solve the problem, send BLDrecord.txt to: discuss@linmodems.org
Попробуй это:
http://linmodems.technion.ac.il/package ... 1a2.tar.gz
http://linmodems.technion.ac.il/package ... 1a2.tar.gz
Опыт растет прямо пропорционально выведенному из строя оборудованию
-
Anonymous
-
Speccyfan
- Неотъемлемая часть форума
- Сообщения: 540
- Зарегистрирован: 18 дек 2004, 15:15
- Откуда: Polotsk
- Контактная информация:
У меня вот похожая проблема с Intel536ep
модули загружены, посмотрел /proc/devices
у меня там строчка есть
62 i536ep
создаю устройство:
# mknod /dev/536ep c 62 1
1 это я взял из инструкции, а вообще поподробней можно, что это за мажор и минор номера ?
Потом сделал ссылку на /dev/modem но нифига не работает.
Модули загружены.
модули загружены, посмотрел /proc/devices
у меня там строчка есть
62 i536ep
создаю устройство:
# mknod /dev/536ep c 62 1
1 это я взял из инструкции, а вообще поподробней можно, что это за мажор и минор номера ?
Потом сделал ссылку на /dev/modem но нифига не работает.
Модули загружены.
Best Regards, Yury Konovalov aka Speccyfan (2:453/53)
Registered Linux User #379588
Registered Linux User #379588
-
*Sasha*
- Неотъемлемая часть форума
- Сообщения: 258
- Зарегистрирован: 12 мар 2005, 01:50
- Откуда: Минск
- Контактная информация:
А если вот так в Suse9.2 то что делать?
linux:/home/sasha/ltmodem-8.31a10 # ./build_module
Lucent/Agere_Systems(AS) DSP chip modems (but Not the AMR or soft PCI chipsets)
are supported by the the resources of this kit.
AS maintainer S. Sarkar develops the code on a Red Hat Linux test bed.
The lt_serial.o Serial Interface module comes under GPL and is Open Source.
The lt_modem.o code is entirely proprietary, though partially Open Source.
Adaptation to ongoing changes in Linux source code is enabled by the Open Source comp
onents.
Critical AS proprietary information is pre-complied in ltmdmobj.o,
whose constituents are functionally not affected by minor Linux source code changes.
Volunteer maintainers periodically receive code updates from AS.
Through the contributions of Many described in CREDITS, there are
enhancements in utility, ease of installation and documentation.
Mark Spieth initiated this ltmodem compiler kit series.
Chris Hebeisen introduced the Configure implementation, bringing Newbie friendliness.
Marv Stodolsky is culpable for the verbose messaging.
Within DOCs/, Ltmodem.html has URLs to many particular usage cases.
Volunteers assemble the ltmodem-version.deb and
ltmodem-version.rpm Installers for the User Community as Linux source code evolves
utiliizing the resources of this compiler kit series.
If new to compiling, read the ModemCompiling.txt which is being output, to guide
proper set up your kernel-sources. The kernel-source package as installed does
NOT in general match an installed kernel, but one of several alternative kernels.
Thus with a niave usage, all could be completed well technically.
BUT the installed drivers might not be compatible with your kernel,
of even reside in the needed /lib/modules/Kernel_Version/ tree.
To continue, Enter
This compilation process is likely Not necessary to work through,
if the only need is modem drivers matching the standard kernel of the
following Linux distributions: Debian, Red Hat, Mandrake, SuSE and Connectiva
Volunteers have already compiled most standard drivers. For more current releases,
those available compatible with your System requirements will be later listed.
They are available for download as ltmodem-version.rpm and
ltmodem-version.deb Installers from a repository, http://ltmodem.heby.de
If your System can use one of these Installers, you will be informed below.
Many installers for older kernels are available at:
http://linmodems.technion.ac.il/packages.html
The compiling process is a learning experience for Newbies.
We strongly recommend that you DO learn it sometime.
But getting on the Internet under Linux should have first priority.
This kit provides several diagnostics aids and good documentation.
Continuing will do no harm. Useful diagnostic information
on your system will be written to BLDrecord.txt,
with direction to documentation if a failure occurs.
At a minimum, Do keep the DOCs/ and utils/ folders and become familiar
with the resources therein.
To continue: Enter
=================================================================
This is the version 8.31a10 of the compiler + installer kit
8.31 corresponds to the version of the core Agere Systems DSP code.
a10 designation that follows reflects NO improvement in DSP code.
Rather peripheral driver, added diagnostics and installer improvements
are reflected. They are progressively implemented as Users report problems
or the Linux kernel evolves.
The modem drivers will serve with Linux kernels beginning with 2.2.2, the current
2.4.nn series, and the 2.5.nn development kernels.
However support was broken in the early 2.4.n-test series.
When there is a Red Hat 2.6.nn release, AS will then update the code
If your PC is being well served with this 8.31a10,
there is NO Benefit in using a more recent version
until there is an update in the Agere driver code, say 8.26 to 9.00.
But if the driver installation for a new kernel should in some way fail,
please do download the most recent ltmodem-VER.tar.gz
before sending a query to discuss@linmodems.org,
because the problem may already be solved.
This build_module script only compiles drivers,
with their installation managed by subsequent commands.
Thus ./build_module can be rerun for education or amusement,
without as yet committing changes to your System.
For general instructions: Enter
=================================================================
All should work automatically for most Linux installations/distributions,
IF a complete kernel-headers/ folder is available:
through a symbolic link: /lib/modules/KernelVersion/build --> PATH_to/kernel-headers/
at the classical /usr/src/ position.
Otherwise a symbolic link will be necessary:
ln -s PATH_to/kernel-headers/ /usr/src/linux
Read ModemDriverCompiling.txt if an explanation is needed about kernel-headers.
To compile modules for a kernel other version than 2.6.8-24-default, such as version2.2.17-3test, use syntax:
./build_module 2.2.17-3test
where the version.h in the kernel-headers/ folder has 2.2.17-3test
If desirable to make a record for trouble shooting purposes,
Abort with Ctrl-C. Then the process can be recorded to ltrecord.txt :
./build_module | tee ltrecord.txt
To continue: Enter
====================================================================
Diagnostic information is progressively being written to BLDrecord.txt .
Often, contents of BLDrecord.txt will aid in solving a problem.
The Linux distribution is: SuSE, SuSE Linux 9.2 (i586)
VERSION = 9.2
End of distribution check.
UPDATE=2004_Nov_26
TMPM=0tmpfile
Providing detail for device at PCI_bus 0000:00:0c.0
with vendor-ID:device-ID
----:----
Class 0780: 11c1:044c Communication controller: Agere Systems (former Lucent Microelectronics) LT WinModem (rev 02)
SubSystem 11c1:044c Agere Systems (former Lucent Microelectronics) LT WinModem
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at e6005000 (32-bit, non-prefetchable)
I/O ports at d800
-----PCI_IDs------- --CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 11c1:044c 11c1:044c SuSE 2.6.8-24-default 3.3.4 3.3.4 i686
IDENT=AGERE
PCIDEV=11c1:044c
Vendor=11c1
The modem has a supported Lucent/Agere DSP (digital signal processing) chipset
with primary PCI_ID: 11c1:044c
DSP=1
To continue: Enter
==================================================
Checking for any preliminary complications.
Bad links to /usr/include not evident.
The kernel supports only single processor motherboards.
To continue: Enter
==================================================
OK thus far.
To begin acquisition of compiling information: Enter
Removing old makings and expanding a clean source.tar.gz
Setting BLDrecord.txt link within source/ folder.
lrwxrwxrwx 1 root root 16 2005-03-17 20:14 BLDrecord.txt -> ../BLDrecord.txt
Setting ./tmpfile link within source/ folder.
lrwxrwxrwx 1 root root 12 2005-03-17 20:14 ./tmpfile -> .././tmpfile
Following a successful check for matching kernel-headers,
the modem drivers will be compiled for the current kernel version: 2.6.8-24-default
To start resource tests: Enter
Performing a configure trial and capturing the report to ../conf-report.txt.
Parsing the report:
No evident problems.
grep: Makefile: No such file or directory
The check for compilation tools and general resources was successful.
Within DOCs/ there is an annotated conf-report.txt
The Makefile and down steam installation scripts have been created.
To continue:
Enter
Next checking utilty versions,
Version_min
Utility or range for kernels
name 2.2.16 2.4.18 Actual_version
-------------------------------------------------------------------
Gnu C 2.7.2.3 2.95.3-2.9.99 3.3.4
Gnu make 3.77 3.79.1 3.80
binutils 2.8.1.0.23 2.9.1.0.25 2.15.91.0.2
-------------------------------------------------------------------
The gcc compiler resources available are:
----------------------------
-rwxr-xr-x 1 root root 101529 2004-10-02 02:56 /usr/bin/gcc
-rwxr-xr-x 1 root root 15900 2004-10-02 02:56 /usr/bin/gccbug
----------------------------
with your System currently using version 3.3.4
Do NOT mix the major versions of compilers for the kernel and modem drivers
or your System will crash! The following releases are using gcc version 3.2.x :
Mandrake 9, Redhat 8 and SuSE 8.1 in November 2002.
To continue:
Enter
To begin compilation of lt_modem.o and lt_serial.o, Enter
To avoid faulting Systems with an Enviromental setting: make -e
make
is the compiling command used with build_module.
To modify "make" invocation on your System, if desirable,
edit the build_module line below: MAKEE
make: *** Не заданы цели и не найден make-файл. Останов.
Checking for driver products:
Compilation of lt_modem.ko failed,
Do assess whether your utilities are up to date as listed within 1ST-READ!
Read Compile_properly.txt from DOCs/.
If you cannot solve the problem, send BLDrecord.txt to: discuss@linmodems.org
linux:/home/sasha/ltmodem-8.31a10 #
linux:/home/sasha/ltmodem-8.31a10 # ./build_module
Lucent/Agere_Systems(AS) DSP chip modems (but Not the AMR or soft PCI chipsets)
are supported by the the resources of this kit.
AS maintainer S. Sarkar develops the code on a Red Hat Linux test bed.
The lt_serial.o Serial Interface module comes under GPL and is Open Source.
The lt_modem.o code is entirely proprietary, though partially Open Source.
Adaptation to ongoing changes in Linux source code is enabled by the Open Source comp
onents.
Critical AS proprietary information is pre-complied in ltmdmobj.o,
whose constituents are functionally not affected by minor Linux source code changes.
Volunteer maintainers periodically receive code updates from AS.
Through the contributions of Many described in CREDITS, there are
enhancements in utility, ease of installation and documentation.
Mark Spieth initiated this ltmodem compiler kit series.
Chris Hebeisen introduced the Configure implementation, bringing Newbie friendliness.
Marv Stodolsky is culpable for the verbose messaging.
Within DOCs/, Ltmodem.html has URLs to many particular usage cases.
Volunteers assemble the ltmodem-version.deb and
ltmodem-version.rpm Installers for the User Community as Linux source code evolves
utiliizing the resources of this compiler kit series.
If new to compiling, read the ModemCompiling.txt which is being output, to guide
proper set up your kernel-sources. The kernel-source package as installed does
NOT in general match an installed kernel, but one of several alternative kernels.
Thus with a niave usage, all could be completed well technically.
BUT the installed drivers might not be compatible with your kernel,
of even reside in the needed /lib/modules/Kernel_Version/ tree.
To continue, Enter
This compilation process is likely Not necessary to work through,
if the only need is modem drivers matching the standard kernel of the
following Linux distributions: Debian, Red Hat, Mandrake, SuSE and Connectiva
Volunteers have already compiled most standard drivers. For more current releases,
those available compatible with your System requirements will be later listed.
They are available for download as ltmodem-version.rpm and
ltmodem-version.deb Installers from a repository, http://ltmodem.heby.de
If your System can use one of these Installers, you will be informed below.
Many installers for older kernels are available at:
http://linmodems.technion.ac.il/packages.html
The compiling process is a learning experience for Newbies.
We strongly recommend that you DO learn it sometime.
But getting on the Internet under Linux should have first priority.
This kit provides several diagnostics aids and good documentation.
Continuing will do no harm. Useful diagnostic information
on your system will be written to BLDrecord.txt,
with direction to documentation if a failure occurs.
At a minimum, Do keep the DOCs/ and utils/ folders and become familiar
with the resources therein.
To continue: Enter
=================================================================
This is the version 8.31a10 of the compiler + installer kit
8.31 corresponds to the version of the core Agere Systems DSP code.
a10 designation that follows reflects NO improvement in DSP code.
Rather peripheral driver, added diagnostics and installer improvements
are reflected. They are progressively implemented as Users report problems
or the Linux kernel evolves.
The modem drivers will serve with Linux kernels beginning with 2.2.2, the current
2.4.nn series, and the 2.5.nn development kernels.
However support was broken in the early 2.4.n-test series.
When there is a Red Hat 2.6.nn release, AS will then update the code
If your PC is being well served with this 8.31a10,
there is NO Benefit in using a more recent version
until there is an update in the Agere driver code, say 8.26 to 9.00.
But if the driver installation for a new kernel should in some way fail,
please do download the most recent ltmodem-VER.tar.gz
before sending a query to discuss@linmodems.org,
because the problem may already be solved.
This build_module script only compiles drivers,
with their installation managed by subsequent commands.
Thus ./build_module can be rerun for education or amusement,
without as yet committing changes to your System.
For general instructions: Enter
=================================================================
All should work automatically for most Linux installations/distributions,
IF a complete kernel-headers/ folder is available:
through a symbolic link: /lib/modules/KernelVersion/build --> PATH_to/kernel-headers/
at the classical /usr/src/ position.
Otherwise a symbolic link will be necessary:
ln -s PATH_to/kernel-headers/ /usr/src/linux
Read ModemDriverCompiling.txt if an explanation is needed about kernel-headers.
To compile modules for a kernel other version than 2.6.8-24-default, such as version2.2.17-3test, use syntax:
./build_module 2.2.17-3test
where the version.h in the kernel-headers/ folder has 2.2.17-3test
If desirable to make a record for trouble shooting purposes,
Abort with Ctrl-C. Then the process can be recorded to ltrecord.txt :
./build_module | tee ltrecord.txt
To continue: Enter
====================================================================
Diagnostic information is progressively being written to BLDrecord.txt .
Often, contents of BLDrecord.txt will aid in solving a problem.
The Linux distribution is: SuSE, SuSE Linux 9.2 (i586)
VERSION = 9.2
End of distribution check.
UPDATE=2004_Nov_26
TMPM=0tmpfile
Providing detail for device at PCI_bus 0000:00:0c.0
with vendor-ID:device-ID
----:----
Class 0780: 11c1:044c Communication controller: Agere Systems (former Lucent Microelectronics) LT WinModem (rev 02)
SubSystem 11c1:044c Agere Systems (former Lucent Microelectronics) LT WinModem
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at e6005000 (32-bit, non-prefetchable)
I/O ports at d800
-----PCI_IDs------- --CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 11c1:044c 11c1:044c SuSE 2.6.8-24-default 3.3.4 3.3.4 i686
IDENT=AGERE
PCIDEV=11c1:044c
Vendor=11c1
The modem has a supported Lucent/Agere DSP (digital signal processing) chipset
with primary PCI_ID: 11c1:044c
DSP=1
To continue: Enter
==================================================
Checking for any preliminary complications.
Bad links to /usr/include not evident.
The kernel supports only single processor motherboards.
To continue: Enter
==================================================
OK thus far.
To begin acquisition of compiling information: Enter
Removing old makings and expanding a clean source.tar.gz
Setting BLDrecord.txt link within source/ folder.
lrwxrwxrwx 1 root root 16 2005-03-17 20:14 BLDrecord.txt -> ../BLDrecord.txt
Setting ./tmpfile link within source/ folder.
lrwxrwxrwx 1 root root 12 2005-03-17 20:14 ./tmpfile -> .././tmpfile
Following a successful check for matching kernel-headers,
the modem drivers will be compiled for the current kernel version: 2.6.8-24-default
To start resource tests: Enter
Performing a configure trial and capturing the report to ../conf-report.txt.
Parsing the report:
No evident problems.
grep: Makefile: No such file or directory
The check for compilation tools and general resources was successful.
Within DOCs/ there is an annotated conf-report.txt
The Makefile and down steam installation scripts have been created.
To continue:
Enter
Next checking utilty versions,
Version_min
Utility or range for kernels
name 2.2.16 2.4.18 Actual_version
-------------------------------------------------------------------
Gnu C 2.7.2.3 2.95.3-2.9.99 3.3.4
Gnu make 3.77 3.79.1 3.80
binutils 2.8.1.0.23 2.9.1.0.25 2.15.91.0.2
-------------------------------------------------------------------
The gcc compiler resources available are:
----------------------------
-rwxr-xr-x 1 root root 101529 2004-10-02 02:56 /usr/bin/gcc
-rwxr-xr-x 1 root root 15900 2004-10-02 02:56 /usr/bin/gccbug
----------------------------
with your System currently using version 3.3.4
Do NOT mix the major versions of compilers for the kernel and modem drivers
or your System will crash! The following releases are using gcc version 3.2.x :
Mandrake 9, Redhat 8 and SuSE 8.1 in November 2002.
To continue:
Enter
To begin compilation of lt_modem.o and lt_serial.o, Enter
To avoid faulting Systems with an Enviromental setting: make -e
make
is the compiling command used with build_module.
To modify "make" invocation on your System, if desirable,
edit the build_module line below: MAKEE
make: *** Не заданы цели и не найден make-файл. Останов.
Checking for driver products:
Compilation of lt_modem.ko failed,
Do assess whether your utilities are up to date as listed within 1ST-READ!
Read Compile_properly.txt from DOCs/.
If you cannot solve the problem, send BLDrecord.txt to: discuss@linmodems.org
linux:/home/sasha/ltmodem-8.31a10 #
Debian
